Any ETA about the offsets on axis for texts and indicators? The actually positioning of text and indicators is a little crap :(

I have tried a lot of combinations and never stays were I want

Powerbar - middle

Unitframe - Inside, middle

Regards

So, I've been a PB user since bc now i used Pitbull3 for the longest time and had recently upgraded to Pitbull4. I only have 1 question and it might just be a matter of me having to reset my WTF/WDB folders, but my quesiton is this. . .

q: How do i get my HP to show up on bars..(32123k)i can only see deficits.

This is killing me. Please help.

Thank you seattlegirl! I was sure my question was already posed by someone, but I didn't think it would be very fun sifting through 320 comments looking for an answer.

FOR THOSE WHO ARE COMMENTING ABOUT NOT BEING ABLE TO CONFIGURE SEPARATE FRAMES:

The ability is there, and it is wonderfully arranged with all the beauty and precision of 3.0, but far easier to use!

You create a template for each frame. This means that you can create a template for your target frame, your raid frame, your party frame, your pet frame, et cetera. You then determine the function for each template you've created (Template #1 is used for the Target function, Template #2 for the Pet Target frame, and so on).

You can also share templates between frames. For example, my raid and party frames have the same template (in my case, I named that template "businesstime").

Remember: form and function. You create a form (a template) and determine it's function (Target Frame, Raid Frame, et cetera).

So the ability is there, and if you can't find it, then you just haven't figured out 4.0 yet. So keep looking!

I get the following error on login, but only with a DK.

[2009/05/22 04:18:50-55-x1]: PitBull4-r20090522064529\Modules\PowerBar\PowerBar.lua:131: table index is nil CallbackHandler-1.0-3 (Atlas):146: in function <Interface\AddOns\Atlas\Libs\CallbackHandler-1.0.lua:146> <string>:"safecall Dispatcher[2]":4: in function <[string "safecall Dispatcher[2]"]:4> <in C code>: ? <string>:"safecall Dispatcher[2]":13: in function `?' CallbackHandler-1.0-3 (Atlas):91: in function `Fire' AceEvent-3.0-3 (AuctionLite):119: in function <...ddOns\AuctionLite\Libs\AceEvent-3.0\AceEvent-3.0.lua:118>

-

I may be blind and foolish, but is it not possible to have separate configurations for different frames? Eg. auras located at the bottom of my player unit frame but at the top of my target unit frame? I absolutely love the changes in version 4.0 and it would be a shame for me to have to go back to 3.0.

Well I disabled some more modules right now, I actually don't use Threatbar, Combatfader and some others. Maybe this helps.

With the newest version I couldn't reproduce memory usage of >10MB in AV like I had in Ulduar-25 on Monday. However, disabling the dogtags module lowers the memory usage from like 3.3MB to 2.3MB when idle in AV, whith just 5 groups (25-man) enabled (pets disabled). Framerate was also not that bad as on monday, looked rather "normal". Disabling other modules gives no noticable improvements (well disabling health bar probably would. ;)

Huge lag spikes occur when someone joins the battleground or I enable pets and e.g. hunters are dismounting. I'll take a further look at it when raiding 25-mans again tomorrow evening.

Toml: I am having similar issues on my Mage. After updating yesterday I am having significantly worse performance out of this addon. I hadn't updated Pitbull for about 2 days before, and I am going to try going back to the older one to see if it alleviates any of the issues as well.

Did you have noticable performance issues with later versions? I think it might be, because I use many dogtags (hots, beacon, sacred shield, Shieldwall/Barkskin etc. on tanks, icons for ulduardebuffs like Unbalancing Strike, Sanity, Bombs on XT, etc.) in my raidframes. Just a guess.

a) Paladin

b) Modules I switched off: Border, Castbar, Highlight, Portrait, Sounds

c) Raid, Player, Target, ToT, Focus, ToF, Group 1 to 8 are always enabled. I use the method to build a Unit-group for every Raidgroup with filter set to the associated grp. Maybe I should disable grp5 to grp8 in a 25 man raid. Could this be a problem although they are empty?

d) I tried to figure it out when exactly, but the framerate always starts dropping at the beginning of a fight, throughout the whole fight, so nothing special. Memory usage was also going up from sth. like 2.5MB to >10MB. I actually didn't test it that long during the raid, cause healing Mimiron in P2 with 2-3fps is ... well ... tricky, so I switched back to the older version rather quickly.

But if I find the time tomorrow, I will try to test it in AV with 5 grps enabled and switch off some of the modules, especially Dogtags.

Thanks so far.

reported this at the official thread already, but having major trouble with the bar "fullness"/text upgrading properly. This is mostly an issue with my own healthbar, the target of target seems to be working properly.

I've tried vers.r20090518073645 in Ulduar-25 yesterday. Performance was even worse than with the version I used before (r20090510210454) despite all the perf improvements. fps was dropping to 2-3 fps during fights (idle: 50-60fps). Using the older version (r20090510210454) the fps "just" drops down to 10-15fps.

I never haven't noticed any issues; although I don't display raid frames when the group exceeds 25 members. But I'll take your word for it seeing as you're an Author lol.

Any idea what the deal is with the curse updater and the failed downloads, or is that just me?

[[psyn://addonservice.curse.com/addonservice.asmx/GetAddOn?pAddOnId=7522|Install via curse client]] seems to have stopped working; for me at least. It detects that there's been an update, however I get "Download Failed" when attempting to update from within the client.

I was also wondering why you guys haven't hosted 4.0 on curse. It seems form a user's perspective like it's more then ready to replace the 3.0 currently hosted.

Keep up the good work! I love the new config layout!